We use cookies to enhance your experience. By continuing to browse this site you agree to our use of cookies. More info.
As the world becomes more technology-driven than ever, there is an increasing demand for better and quicker electronics and computers. Spintronics is a new innovation that encodes data using an electron’s spin as well as its charge state, thereby making the whole system faster and more efficient.
Image Credit: Tokyo Institute of Technology.
To realize the potential of spintronics, ferromagnetic nanowires with strong coercivity (resistance to changes in magnetization) are required, and L10-ordered (a form of crystal structure) cobalt–platinum (CoPt) nanowires in particular.
Traditional fabrication processes for L10-ordered nanowires include heat treatment to enhance the physical and chemical properties of the material, annealing on the crystal substrate; pattern transfer onto the substrate via lithography; and eventually, chemical layer removal via etching.
Eradicating the etching procedure by directly manufacturing nanowires onto the silicon substrate might result in a significant breakthrough in spintronic device fabrication. Unfortunately, when directly fabricated nanowires are annealed, the inherent stresses in the wire cause them to change into droplets.
A group of scientists headed by Professor Yutaka Majima of the Tokyo Institute of Technology has discovered a solution to the problem. The researchers described a new fabrication method for producing L10-ordered CoPt nanowires on silicon/silicon dioxide (Si/SiO2) substrates. The study was published in the journal Nanoscale Advances.
Our nanostructure-induced ordering method allows the direct fabrication of ultrafine L10-ordered CoPt nanowires with the narrow widths of 30nm scale required for spintronics. This fabrication method could further be applied to other L10-ordered ferromagnetic materials such as iron–platinum and iron–palladium compounds.
Yutaka Majima, Professor, Tokyo Institute of Technology
In this work, the investigators first coated a Si/SiO2 substrate with a substance called a “resist” and exposed it to electron beam lithography and evaporation to form a stencil for the nanowires.
The substrate was then covered with a multilayer of CoPt. The deposited samples were then “lifted off,” leaving CoPt nanowires behind, and the nanowires were then annealed at high temperatures. The team also used various characterization techniques to evaluate the produced nanowires.
Researchers discovered that the nanowires acquired L10-ordering throughout the annealing procedure. This transition was caused by atomic interdiffusion, surface diffusion, and exceptionally high internal stress at the nanowires’ ultrasmall curvature radii of 10 nm. They also discovered that the nanowires have a high coercivity of 10 kiloOersteds (kOe).
The internal stresses on the nanostructure here induce the L10-ordering. This is a different mechanism than in previous studies. We are hopeful that this discovery will open up a new field of research called ‘nanostructure-induced materials science and engineering.’
Yutaka Majima, Professor, Tokyo Institute of Technology
The breakthrough fabrication technique’s broad applicability and ease of use will undoubtedly make a substantial contribution to the field of spintronics research.
Toyama, R., et al. (2022) Nanostructure-induced L10-ordering of twinned single-crystals in CoPt ferromagnetic nanowires. Nanoscale Advances. doi.org/10.1039/D2NA00626J.
Source: https://www.titech.ac.jp/english
Do you have a review, update or anything you would like to add to this news story?
Ebbe Sloth Andersen, Ph.D.
In this interview, AZoNano speaks with Ebbe Sloth Anderson about a new software-based 'RNA origami' technique that can be used to design RNA molecules that fold into compact and rigid shapes.
AZoNano speaks with CityU's Dr.Zhiyuan Zeng about a new approach to in situ liquid cell transmission electron microscopy that holds great promise for the real-time viewing of complex electrochemical reactions at the nanoscale.
Dr. Meganne Christian, Dr. Ghada Dushaq
AZoNano has collaborated with the Graphene Flagship to highlight two outstanding women innovating the field of graphene research.
The MiniCapt® Pro is a remote microbial air sampler that is ideal for the pharmaceutical manufacturing industry.
This product profile outlines the NanoRacer High-Speed AFM from Bruker JPK.
NMR spectroscopy is a characterization technique that is extensively used by chemical researchers.
AZoNano.com - An AZoNetwork Site
Owned and operated by AZoNetwork, © 2000-2023